المنتج

كيف تعمل معنا?

للبدء، يُرجى مشاركة المواصفات التفصيلية لمتطلباتك. مهندسو المبيعات المحترفون لدينا متاحون على مدار الساعة طوال أيام الأسبوع لمساعدتك في الإجابة عن أي أسئلة. لا تتردد في التواصل معنا عبر البريد الإلكتروني أو الهاتف أو زيارتنا شخصيًا.

الأسئلة المتداولة

نحن مصنعون محترفون لمعدات الاختبار، ولدينا فريق البحث والتطوير الخاص بنا، وورشة الإنتاج، ونظام مراقبة الجودة، ومغادرة التسويق

نقدم ضمانًا لمدة 12 شهرًا وصيانة مدى الحياة. يسري الضمان على المشتري الأصلي بأن المعدات ستكون خالية من أي عيب في المواد أو التصنيع لمدة سنة واحدة من تاريخ الشراء. تغطي الضمانات فقط العيوب التي تنشأ في ظل الاستخدام العادي والخدمة العادية، باستثناء أي عيوب وأضرار ناتجة عن سوء الاستخدام أو التغيير أو التركيب غير السليم أو الإهمال أو الظروف البيئية المعاكسة، وليس عن مشاكل الجودة.

عادة ما يكون وقت التسليم حوالي 15 يوم عمل بعد الدفع. بالنسبة لبعض المنتجات الخاصة المخصصة، سيستغرق الأمر من 15 إلى 30 يوم عمل حسب المعلمة الفنية لمتطلبات العميل.

اتصل بنا

البريد الإلكتروني: info@kvhipot.com
الهاتف: +86 18062060691
واتساب +8618062060691

أو

جهاز اختبار تشوه لف لف المحولات KVRB

Power transformer winding deformation tester uses the internal fault frequency response analysis (FRA) method to measure the internal fault of transformer windings based on a measurement of the characteristics of transformer internal windings.

تفاصيل المنتجات

الوصف

General Information

Power transformer winding deformation tester uses the internal fault frequency response analysis (FRA) method to measure the internal fault of transformer windings based on a measurement of the characteristics of transformer internal windings. This method can accurately identify transformer internal faults.

 

Main الميزة

  1. Adoptshigh-speed, highly integrated microprocessor.
    Communication USB interface used between a laptop and instrument.
    3. Wireless WIFI interface (optional) used between the laptop computer and instrument.
  2. Hardware adopts dedicated DDS digital high-speed scanning technology (USA), which can accurately diagnose the faults like winding distorted, bulged, shift, tilt, inter-turn short-circuit deformation and inter-phase contact short-circuit.
    5. High-speed dual-channel 16-bit A/D sampling (in field test, move tap changer, and the wave curve shows obvious change) .
    6. Signal output amplitude is adjusted by software, and the peak value of amplitude is ± 10V.
    7. The computer will automatically analyze the test results and generate electronic documents (Word)
  3. The instrument has dual measurement features: linear frequency scanning measurement and segment frequency scanning measurement, compatible with measurement mode of two technical groups in China
  4. The amplitude-frequency characteristics are in line with the national technical specifications on amplitude-frequency characteristics tester. X-coordinate (frequency) has linear indexing and logarithmic indexing, so you can print out the curve with linear indexing and logarithmic indexing. The user can choose either according to actual needs.
    10. Automatic test data analysis system,
    Compare between A, B, C -phases in winding similarity comparison, and
    the analysis results are:
    ① excellent consistency
    ② good consistency
    ③ poor consistency
    ④ rather poor consistency

Compare winding deformation by calling the original data and comparing it with the current data of the same phase, namely A-A, B-B, C-C, and the analysis results are:
① normal winding
② mild deformation
③ moderate deformation
④ severely deformation

  1. Word electronic document can be automatically generated for saving and printing.

Technical parameters

Scan mode:
1. Linear scanning distribution
Scanning measurement range: (10Hz) – (10MHz) 40000 scanning point, resolution 0.25kHz, 0.5kHz and 1kHz
2. Segment frequency scanning measurement distribution
Frequency scanning measurement range: (0.5kHz) – (1MHz), 2000 scanning points ;
(0.5kHz) – (10kHz)
(10kHz) – (100kHz)
(100kHz) – (500kHz)
(500kHz) – (1000kHz)

arالعربية

استفسر الآن